Isolated DIN Rail Repeater/Splitter for Current Signals

DRSL-SP1

345,410원 DRSL-SP1

가격 확인

Isolation and Conversion of Current Signals
Splitter Function: 1 Current Input—2 Current Outputs
Slimline Housing—Only 6 mm (0.24") Wide
Fast Response Time <7 ms
High Accuracy, <0.05% of Span
Easy-to-Use—No Setup Needed

프로세스 측정 / 제어 장비 - 관련 제품 보기

설명

The DRSL-SP1 isolated repeater/ splitter provides a competitive choice in terms of both price and technology for galvanic isolation of current signals to SCADA systems or PLC equipment. Two current outputs are provided which mirror the single current input.

The DRSL-SP1 can be used for signal conversion of a standard process current signal into two individual analog signals. The unit offers 4-port isolation, provides surge suppression and protects control systems from transients and noise. The DRSL-SP1 also eliminates ground loops and can be used for measuring floating signals. Low power consumption facilitates DIN rail mounting without the need for any air gap. Measurement ranges are factory calibrated. The unit operates over a wide temperature range from -25 to 70°C (-13 to 158°F).

SPECIFICATIONS
CURRENT INPUT
    Measurement Range: 0 to 20.5 mA
    Functional Range: 0 to 23 mA
    Input Voltage Drop: <1.5 Vdc

CURRENT OUTPUT
Number of Outputs: 2
    Signal Range: 0 to 20.5 mA (span)
    Load: 23 mA/300 Ω maximum
    Load Stability: ≤0.01% of span/100 Ω (span = 0 to 20 mA)
    Current Limit: ≤28 mA

GENERAL
Supply Voltage (via Power Rail or Connectors): 16.8 to 31.2 Vdc
Power Consumption: 0.8 W max
Internal Consumption: 0.4 W typical/0.65 W max
Isolation: Input/output 1/ output 2/supply
Isolation Voltage (Test): 2.5 kVac
Isolation Voltage (Working): 300 Vac
Signal/Noise Ratio: > 60 dB
Response Time (0 to 90%, 100 to 10%): <7 ms
Accuracy: < ±0.05% of span
Temperature Coefficient: <±0.01% of span/°C
EMC Immunity Influence: < ±0.5% of span
Extended EMC Immunity
    NAMUR NE 21, A Criterion, Burst: <±1% of span

ENVIRONMENTAL
Operating Temperature: -25 to 70°C (-13 to 158°F)
Storage Temperature: -40 to 85°C (-40 to 185°F)
Calibration Temperature: 20 to 28°C (68 to 82°F)
Relative Humidity: 0 to 95% RH non-condensing
Protection Degree: IP20
Installation Area: Pollution degree 2 and measurement/overvoltage category II

MECHANICAL
Dimensions: 113 H x 6.1 W x 115 mm D (4.4 x 0.24 x 4.5")
Weight: 70 g (0.15 lb) approx
DIN Rail Type: DIN EN 60715 - 35 mm
Wire Size: 0.13 x 2.5 mm2/AWG 26 to 12 stranded wire
Screw Terminal Torque: 0.5 Nm

가격 확인(원하는 수량을 기입하십시오.)

다른 고객님이 함께 구매하신 제품 : 이 아이콘을 클릭하시면 기존 고객들께서 이 제품을 주문할 때 함께 구매하신 제품리스트가 보입니다.

제품 번호/Desc.

수량

설명

DRSL-SP1

345,410원

배송: 2 주

Isolated repeater/splitter for current signals

Accessories

DRSL-PWR-RAIL

254,530원

배송: 2 주

Power rail (with cover and two end covers, one right hand and one left hand), 1 m (3.3') length

DRSL-PCU

174,900원

배송: 2 주

Power connector unit, 24 Vdc/2.5 A output to power rail

DRSL-MOD-STOP

11,500원

배송: 4 주

Module stop (screwed onto power rail to support and hold mounted devices)

† 모든 가격은 원화로 표시되어 있습니다.
주문 예: (1) DRSL-MOD-STOP Module stop (screwed onto power rail to support and hold mounted devices), 11,500원 plus (1) DRSL-PCU Power connector unit, 24 Vdc/2.5 A output to power rail, 174,900원 plus (1) DRSL-PWR-RAIL Power rail (with cover and two end covers, one right hand and one left hand), 1 m (3.3') length, 254,530원 plus (1) DRSL-SP1 Isolated repeater/splitter for current signals, 345,410원, 11,500 + 174,900 + 254,530 + 345,410 = 786,340원

제품 메뉴얼:

다운로드 Installation Guide for Signal Conditioners

다운로드 DIN Rail Isolators and Signal Conditioners

관련 제품: